Orari di apertura 
Lun-Ven 9-13 14-18
Sabato  9-13  14-16

Domenica Chiuso


Seleziona il tipo di ricerca:


ATTENZIONE: Alcune informazioni relative al prodotto sono visibili soltanto agli utenti registrati!

Torna alla pagina precedente TORNA CATALOGO / ACCESSORI RC / RADIOCOMANDI / .7 RICEVENTI AIR STANDARD / GRA33516

Articolo : GRA33516 Disponibilità :  Scarsa  Scarsa


    RICEVENTE GR32 DUAL HOTT

    RICEVENTE GR32 DUAL HOTT   RICEVENTE GR32 DUAL HOTT   RICEVENTE GR32 DUAL HOTT
    RICEVENTE GR32 DUAL HOTT

    Fornitore

    The GR-32 receiver can control up to 16 servos

    With the GRAUPNER HoTT 2.4 GHz technology, the receiver has a new hopping telemetry transmission high-frequency unit with state-of-the-art components and the latest software. A hardware antenna diversity system always switches to the better antenna signal and for transmission always uses the antenna that was last used for receiving. This ensures that the back channel data are always sent via the better-positioned antenna. Without additional sensor systems, the parameters receiver voltage and temperature, as well as signal strength are transmitted. Connector for one telemetry sensor and for the sum signal input or output. The receiver does have 6 power inputs for strong servos.

    New receiver software for GR-32 3.80:
    The servo current drain with the GR-32 is often underestimated.
    It is essential to check that your power supply is up to the task by carrying out a comprehensive function and range check with the control surfaces placing a load on the servos.
    The power supply must be designed to cope with the following peak load:
    Peak current = stall current of all servos added together, multiplied by 2.
    The peak currents are considerably lower in ONCE mode than in SAME mode.
    The peak currents are slightly reduced with the new software.
    The modes have been optimised in order to reduce the peak current.
    Optimising ONCE mode:
    Simultaneous output at 20 ms frame rate of:
    Ch 1 + 4
    Ch 2 + 5 + 13
    Ch 3 + 8 + 14
    Ch 6 + 7
    Ch 9 + 10 + 15
    Ch 11 + 12 + 16
    The frame rate is now 20 ms, which means that all known servos and speed controllers will function with this setting.
    Optimisation of SAME mode (frame rate 10 ms or 20 ms):
    Previously the output of channels 1 - 7, 8 - 14 and 15 + 16 was simultaneous.
    The output of the following channels is now simultaneous, in order to reduce peak currents:
    Channels 1 - 5
    Channels 6 - 10
    Channels 11 - 16

    The use of up to 75 channels ensures extreme operating reliability and immunity to external interference.
    The broad reception voltage range of 3.6 V - 8.4 V (functional to 2.5 V) ensures full functionality even when voltage fluctuates.
    Two LEDs signal operating status.
    The sizes and weights have been reduced.
    Receiver input sensitivity and thus the range have been increased further.
    Servo connections in the front panel.
    Failsafe, hold, OFF, and standard (channel 1 failsafe all others hold) programmable.
    Functions with SMART-BOX:

    5 mixers programmable
    Linear, degressive, and exponential programming of servo curves
    SUM signal programmable for input or output on connector S
    Limitation and reversal of servo travels also possible in receiver
    Failsafe, hold, and OFF programmable individually for the servo channels
    Warning thresholds programmable for undervoltage, excess temperature, and low temperature
    Servo test function

    Barcode 4013389456142


    Aggiungi l'articolo alla lista dei desideri!
     Articolo aggiunto alla tua lista dei desideri! 
    RICEVENTE GR32 DUAL HOTT
    Specification

    Dimensions (LxWxH) 63 x 30 x 14 mm
    Frequency 2400 ... 2483,5 MHz
    Aerial length 4 x Draht 145 (Antenne 30) mm
    All-up weight, approx. 24 g
    Modulation 2.4 GHz FHSS
    Range approx. 5000 m
    Charging rate 140 mA
    Temperature range -15 ... 70 °C


    Aggiungi l'articolo alla lista dei desideri!
     Articolo aggiunto alla tua lista dei desideri! 
    RICEVENTE GR32 DUAL HOTT

    Fornitore

    The GR-32 receiver can control up to 16 servos

    With the GRAUPNER HoTT 2.4 GHz technology, the receiver has a new hopping telemetry transmission high-frequency unit with state-of-the-art components and the latest software. A hardware antenna diversity system always switches to the better antenna signal and for transmission always uses the antenna that was last used for receiving. This ensures that the back channel data are always sent via the better-positioned antenna. Without additional sensor systems, the parameters receiver voltage and temperature, as well as signal strength are transmitted. Connector for one telemetry sensor and for the sum signal input or output. The receiver does have 6 power inputs for strong servos.

    New receiver software for GR-32 3.80:
    The servo current drain with the GR-32 is often underestimated.
    It is essential to check that your power supply is up to the task by carrying out a comprehensive function and range check with the control surfaces placing a load on the servos.
    The power supply must be designed to cope with the following peak load:
    Peak current = stall current of all servos added together, multiplied by 2.
    The peak currents are considerably lower in ONCE mode than in SAME mode.
    The peak currents are slightly reduced with the new software.
    The modes have been optimised in order to reduce the peak current.
    Optimising ONCE mode:
    Simultaneous output at 20 ms frame rate of:
    Ch 1 + 4
    Ch 2 + 5 + 13
    Ch 3 + 8 + 14
    Ch 6 + 7
    Ch 9 + 10 + 15
    Ch 11 + 12 + 16
    The frame rate is now 20 ms, which means that all known servos and speed controllers will function with this setting.
    Optimisation of SAME mode (frame rate 10 ms or 20 ms):
    Previously the output of channels 1 - 7, 8 - 14 and 15 + 16 was simultaneous.
    The output of the following channels is now simultaneous, in order to reduce peak currents:
    Channels 1 - 5
    Channels 6 - 10
    Channels 11 - 16

    The use of up to 75 channels ensures extreme operating reliability and immunity to external interference.
    The broad reception voltage range of 3.6 V - 8.4 V (functional to 2.5 V) ensures full functionality even when voltage fluctuates.
    Two LEDs signal operating status.
    The sizes and weights have been reduced.
    Receiver input sensitivity and thus the range have been increased further.
    Servo connections in the front panel.
    Failsafe, hold, OFF, and standard (channel 1 failsafe all others hold) programmable.
    Functions with SMART-BOX:

    5 mixers programmable
    Linear, degressive, and exponential programming of servo curves
    SUM signal programmable for input or output on connector S
    Limitation and reversal of servo travels also possible in receiver
    Failsafe, hold, and OFF programmable individually for the servo channels
    Warning thresholds programmable for undervoltage, excess temperature, and low temperature
    Servo test function

    Barcode 4013389456142


    Aggiungi l'articolo alla lista dei desideri!
     Articolo aggiunto alla tua lista dei desideri! 
Note tecniche e descrizioni dei vari articoli sono pubblicati così come vengono forniti dal costruttore e/o distributore, immagini allegate comprese, e potrebbero contenere delle inesattezze o delle omissioni. Non ci assumiamo quindi alcuna responsabilità a riguardo.

Big Models S.r.l. - via Pier Vittorio Aldini,41 - Roma
Tel. 06 79320402 • Fax. 06 79320402 • P. IVA 04563861006 • Iscr. AEE n° IT09060000006100
La vendita è riservata ai soli commercianti del settore
Mail: info@ingrossomodellismo.it   © Big Models s.r.l. 2005
NOTA: tutti i prodotti da Noi distribuiti recepiscono la DIRETTIVA R.&.T.T.E. 1999/5/CE DECRETO LEGISLATIVO 269/01

  webmaster : Massimo Marra